Calogero Report post Posted July 30, 2021 Buongiorno , ecco il mio nuovo diorama sara un slc maiale che sbuca una rete anti siluro ho cominciato per la base ho fatto la testa con del milliput dopo ho fatto la X in plastica dopo ho inciso a caldo un foglio di plastica transparente per fare la rete non ho trovato un slc maiale in 1/72 , dunque l ho fatto in scratch Scusate il mio italiano sono francese se faccio degli sbagli ditemelo calogero(sono d origine italiana) Share this post Link to post Share on other sites
Calogero Report post Posted July 31, 2021 Ecco oggi ho finito la basetta buona sera a tutti calo Share this post Link to post Share on other sites
Totiano* Report post Posted July 31, 2021 Davvero molto bello e originale, attendiamo l'esito finale! Share this post Link to post Share on other sites
Ocean's One* Report post Posted August 1, 2021 Ottima idea quella di realizzare la basetta con il logo della Decima. Bravo! Ora aspettiamo l’ SLC... Share this post Link to post Share on other sites
STV(CP) * Report post Posted August 20, 2021 Attendiamo il proseguo dei lavori... ottimo.. Share this post Link to post Share on other sites
Calogero Report post Posted January 6, 2022 (edited) buongiorno , ho ricominciato il diorama , ho finalmente sbucato la plastica fa più bello mi sembra, voglio fare degli anelli con del filo di metallo , che saranno sollevati dai marinai, buon anno a tutti calogero Edited January 6, 2022 by Calogero Share this post Link to post Share on other sites
drakkar Report post Posted January 6, 2022 Bella idea, complimentissimi... ci metterai anche i due incursori sopra? Share this post Link to post Share on other sites
Calogero Report post Posted January 6, 2022 5 hours ago, drakkar said: Bella idea, complimentissimi... ci metterai anche i due incursori sopra? si debbo modificare dei soldatini Preiser in 1/72 quello in centro sarà sul maiale , l altro incursore aiuterà a alzare la rete come sul disegno Share this post Link to post Share on other sites
alessandro tesio Report post Posted January 28, 2022 Calogero stupendo, complimenti per l'originalità veramente Bello. Share this post Link to post Share on other sites
Calogero Report post Posted July 17, 2022 buongiorno a tutti ho ripreso il mio modello , ho completato la parte dietro il pilota un saluto calo Share this post Link to post Share on other sites
Ocean's One* Report post Posted July 18, 2022 Ottimo, Calogero. Finalmente il cantiere è ripartito, dai, dai! Solo una domanda: ma quanto è piccolo ?!? Share this post Link to post Share on other sites
Calogero Report post Posted July 19, 2022 ciao Ocean s grazie, fa massimo 9,26 centimetri quando sarà finito Share this post Link to post Share on other sites
Calogero Report post Posted July 23, 2022 piccolo lavoro tutto incollato. solo l incursore non e incollato ho provato di fare il volantino del incurore di davanti un saluto a tutti calogero Share this post Link to post Share on other sites
Ocean's One* Report post Posted July 23, 2022 Ottimo, Calogero. Ormai non manca molto. Mi spieghi come sarà messo l’incursore davanti? E’ sceso dal SLC? Share this post Link to post Share on other sites
Calogero Report post Posted July 23, 2022 Ciao Ocean grazie, vorrei fare l incursore pilota, davanti, e l altro che alza un po della rete come sul disegno ho preparato qualque cerchi per incollare sopra he alzati da il secondo incursore pero sarebbe bene che il pilota si gira per guardare se il dietro del SLC non tocca la rete Buona sera Calogero Share this post Link to post Share on other sites
Ocean's One* Report post Posted July 31, 2022 Grazie, Calogero, ora mi è tutto chiaro. Tienici aggiornati sugli sviluppi. Ciao! Share this post Link to post Share on other sites
Calogero Report post Posted August 5, 2022 buongiorno, ho un po avanzato , tutti i tubi sono stati incollati , ho provato di fare la protezione d elica saldando dei fili sottili , ma non va , cercherò di fare come fanno i modellisti di macchinina ridotte per i raggi delle ruote un saluto dalla Danimarca calogero Share this post Link to post Share on other sites
darth * Report post Posted August 5, 2022 (edited) Ciao a tutti, mi permetto di intervenire per un suggerimento che valuterai, potresti realizzare la protezione dell'elica utilizzando un pezzo delle placchette di alluminio utilizzate per cuocere il cibo nel forno. Sembra una roba rimediata ma ti posso assicurare che si presta bene e fa il suo lavoro. Potresti addirittura utilizzare il disegno di questa parte prendendo spunto dall'immagine riportata sul sito Italeri https://www.italeri.com/prodotto/2677 naturalmente va adattato alla scala che stai utilizzando. Un saluto Edited August 5, 2022 by darth Share this post Link to post Share on other sites